Buttons And Display Panel for Bidetmega

mceclip0.png

[150 & 200 & 400] Stop button: It stops all the functions.

mceclip1.png

[150 & 200 & 400] Rear button: It is a general cleaning mode that can be used when the basic conditions of the anal area are healthy.
· Use the button to select the anal cleaning function.

mceclip2.png

[150 & 200 & 400] Front button: Use this button to select the women’s cleaning function (bidet).

mceclip3.png

[200 & 400]Soothing Wash button (Mode for 400): It is a care cleaning mode that can be used when the conditions of the anal area are not healthy and require a sensitive care.
· Use the button to select the anal cleaning function with a weak water stream.
* Use this mode to use a weaker water stream for cleaning than in the general mode.

mceclip5.png

[150 & 400] Active Mode Button (Mode for 400): It is a function that moves forward and backward. Use this button to experience a delicate and careful wash.

mceclip21.png

[150 & 200] ECO indicator: It turns on when the Eco Mode is selected.

mceclip7.png

[150 & 200] Rinse Nozzle Button: Use this button to clean the nozzle. If you press button, the cleaning water is sprayed on the nozzle and cleaning starts.

*If the Rinse Nozzle button is pressed while the power is off, the cleaning solution is sprayed through the nozzle and the nozzle comes forward and stops for convenient cleaning.

mceclip8.pngmceclip6.png

[200 & 400]Clean Bidet button: Use it to run the manual Clean function. Pressing this button, you can switch the Clean method in the order of Flow Channel Clean → Nozzle Clean → Toilet Clean.
* Manual Clean : Recommended to run twice a day.
* Three-stage auto Clean can operate only if no human body is detected by the seat sensor.
* If you press the button while sitting on the seat, the buzzer sounds and Clean is scheduled. (When the user leaves the seat, Clean is performed.) If you press it one more time afterward, the buzzer sounds and the Clean schedule is canceled.

mceclip10.pngmceclip11.png

[150 & 200 & 400] Child button: It is a function customized to children and their weak skin. The water pressure is the lowest, and the positioning considers children’s small body. If you press this button, cleaning operates for 1 minute and drying for 2 minutes.
* To prevent the case that bidet does not work because it cannot sense the children’s small body, the child function operates with no regard to the sitting sensor’s detection of the user body.
* While the child function is enabled, it is possible to adjust the movement, water pressure, toilet seat temperature, and warm water/drying temperature.
If you press the Child button again while the function is operating, a cleaning or drying function is added to the operation.

mceclip12.pngmceclip13.pngmceclip14.png

[150 & 200 & 400] Nozzle Position button

Use this button to adjust the nozzle position while the cleaning/women’s cleaning function is operating. The nozzle can be moved forward and backward in 5 steps by pressing the button.

*For Bidetmega 400, While using cleansing or women’s cleansing, use this button to adjust the nozzle position back and forth.

mceclip15.pngmceclip16.png

[150 & 200 & 400] Water/Dry Temp. button: Use it to set the water/air temperature. Pressing this button, you can switch the temperature level in the order of Low (green) → Medium (yellow) → High (red) → Off.
* This is used as the warm water temperature indicator while the cleansing/bidet function is operating and as the drying wind temperature indicator while the drying function is operating.

mceclip17.pngmceclip18.png

[150 & 200 & 400] Dry button: Use this button to select the drying function. This function dries off moisture after using the cleaning/women’s cleaning/care cleaning function.

mceclip19.pngmceclip20.png

[150 & 200 & 400] Seat Temp. button: Use it to set the seat temperature. Pressing this button, you can switch the temperature level in the order of Low (green) → Medium (yellow)
→ High (red) → Off.

mceclip0.pngmceclip1.png

[150 & 200 & 400] Water Pressure indicator: You can adjust the water pressure in 5 levels. Every time you press the button, the selected water pressure indicator turns on.

*For Bidetmega 400, press the Water Pressure button to adjust the water pressure to level 1- level 3.

 

mceclip2.png

[400] Cleansing mode indicator: If you press the Mode button, the indicator turns on in the
order of Basic → Active Move → Soothing Wash.